Wrap it. Snap it. Rewards!
Show off your finished wrap. Share a photo and get rewarded!
3M IJ180mC-10LSE Low Surface Energy Custom Print Vinyl Wrap
Upload Artwork
Select Media Option
Calculate Media Usage
This finished size requires paneling. A fixed 1″ overlap is used. The calculator automatically selects a panel orientation and media width, which can be overridden.
File Instructions
Order Summary
$0.00
Gallery
Gallery
Product Details
Product Details
Create professional custom graphics for challenging plastic surfaces with 3M IJ180mC-10LSE Print Wrap Film, professionally printed by Printara. This premium 2 mil white cast vinyl is specifically engineered for low-surface-energy (LSE) plastics commonly found on ATVs, UTVs, dirt bikes, motocross bikes, snowmobiles, and other motorsports equipment.
Featuring 3M Controltac and Comply Adhesive Technology, IJ180mC-10LSE combines a high-tack, pressure-activated adhesive with repositionability and microtechnology air release. Its flexible construction allows the film to conform to compatible curves and contours while providing reliable adhesion to surfaces that can be difficult for standard printable vinyl.
Why Choose 3M IJ180mC-10LSE?
- Designed for LSE Plastics: Specially formulated adhesive bonds to compatible low-surface-energy plastics commonly found on motorsports vehicles and equipment.
- 2 Mil Cast Vinyl: Flexible white film designed to conform to compatible curves, contours, and riveted surfaces.
- High-Tack Adhesive: Permanent adhesive engineered for hard-to-bond substrates that may not work well with standard vehicle wrap films.
- Controltac Technology: Allows sliding, positioning, and repositioning before applying firm pressure to establish adhesion.
- Comply Air-Release Technology: Non-visible micro air-release channels help trapped air escape during installation for smoother results.
- Up to 130% Conformability: Many approved finished graphic constructions can stretch up to 130% while maintaining lift resistance, subject to 3M installation requirements.
- Long-Term Performance: 3M specifies up to 10 years of expected performance for unprinted, unprotected film under defined vertical outdoor exposure conditions.
- Permanent Adhesion: Designed for lasting adhesion rather than clean removability. Removal may damage the underlying surface.
What Can 3M IJ180mC-10LSE Be Used For?
3M IJ180mC-10LSE is designed for custom printed graphics on low-surface-energy plastics and other approved hard-to-bond surfaces. Its high-tack adhesive makes it particularly useful for motorsports graphics, where standard vinyl films may struggle to maintain adhesion.
- ATV & UTV Wraps: Create custom printed graphics for compatible plastic body panels, fenders, and exterior surfaces on all-terrain and utility vehicles.
- Dirt Bike & Motocross Graphics: Produce custom designs for compatible low-surface-energy plastic shrouds, fenders, number plates, and other approved motocross bike components.
- Snowmobile Wraps: Customize compatible snowmobile body panels and plastic surfaces with durable printed graphics designed for challenging substrates.
- Specialty Plastic Graphics: Create branded graphics, decals, and decorative designs for compatible LSE plastics and other difficult-to-bond surfaces.
- Partial Vehicle Wraps : Produce custom graphics for selected vehicle components where the surface requires the specialized adhesion of an LSE-compatible film.
- Fleet Graphics : Create custom branding for specialized commercial equipment and compatible plastic vehicle components that require additional adhesive strength.
Not all plastics have the same surface energy. Verify substrate compatibility and perform adhesion testing before production or installation.
Professional Custom Printing by Printara
Printara provides professional large-format printing for wrap shops, motorsports businesses, graphic designers, and independent installers. Upload your custom artwork, company branding, racing graphics, or specialty designs and have them printed on genuine 3M IJ180mC-10LSE Film.
Whether you're designing graphics for an ATV, UTV, motocross bike, or specialty plastic surface, Printara offers custom printing to help turn your artwork into professional-quality graphics on material engineered for challenging applications.
Choose from available printing options, including standard 6-color printing and 11-color Ultra Sharp HD Printing for projects requiring enhanced image detail, rich colors, and smooth gradients.
Want sharper details and more vibrant prints? Discover the benefits of our 11-Color Ultra Sharp HD Printing technology and learn which printing option is best for your project.
Material Specifications
| Manufacturer | 3M |
| Product | IJ180mC-10LSE |
| Film Type | Cast PVC Vinyl |
| Film Color | White, Opaque |
| Base Finish | Glossy |
| Thickness | 2 Mil (Film Only) |
| Adhesive | High-Tack, Pressure-Activated |
| Adhesive Type | Permanent, LSE-Compatible |
| Air Release | 3M Comply Microtechnology |
| Primary Surfaces | Compatible Low-Surface-Energy Plastics |
| Application Method | Dry Installation |
View Complete 3M IJ180mC-10LSE Media Specifications →
Lamination & Finish Options
Customize the appearance and protection of your printed 3M IJ180mC-10LSE vinyl with Printara's available lamination options. Whether you prefer a glossy finish, subtle satin appearance, or non-reflective matte surface, the selected laminate helps create the desired look for your custom graphics.
- Gloss: A high-shine finish that enhances color depth, vibrancy, and the overall appearance of printed graphics.
- Satin: A smooth, low-sheen finish that balances subtle reflections with rich printed colors.
- Matte: A non-gloss finish that minimizes reflections and provides a clean, understated appearance.
- Avery Gloss Clear Sparkle: A specialty gloss finish featuring a subtle sparkle effect that adds visual depth to custom printed graphics.
- Gloss Plus Protection Film: An enhanced protection option with a glossy finish, designed to provide additional surface protection for printed graphics.
- Satin Plus Protection Film: An enhanced protection option with a smooth satin appearance, combining reduced glare with additional surface protection.
Available finishes and protection options may vary. Select your preferred lamination during product customization. Confirm compatibility, conformability, and application requirements before ordering.
Printing & File Preparation Guides
Need help preparing your artwork or understanding how your custom print is calculated? Scroll down to our Guides section below for step-by-step instructions on:
- How to set up your print file for production.
- How to create contour cut lines for custom-cut graphics.
- How square footage is calculated for printing and pricing.
Estimating a project? Use our Printara Project Cost Calculator to estimate material requirements and costs for your project.
Frequently Asked Questions
What is 3M IJ180mC-10LSE used for?
3M IJ180mC-10LSE is designed for custom printed graphics on compatible low-surface-energy plastics. Common applications include ATVs, UTVs, motocross bikes, snowmobiles, and specialty plastic equipment. Its permanent, high-tack adhesive helps it bond to surfaces that can be challenging for standard printable vinyl.
How long does a printed vehicle wrap last?
Service life depends on the film and laminate combination, installation, environmental exposure, and maintenance. 3M specifies up to 10 years of expected performance for unprinted, unprotected film under defined exposure conditions, which is not a finished-graphic warranty. Learn more in our Vehicle Wrap Durability Guide .
How much does a custom vehicle wrap cost?
Costs vary based on vehicle size, printed square footage, material selection, finishing options, and installation. Learn more in our Full Vehicle Wrap Cost Guide .
How much vinyl do I need to wrap a vehicle?
Material requirements depend on vehicle dimensions, coverage area, panel overlap, and installation needs. For motorsports vehicles, measure each panel and allow additional material for trimming and alignment. See our guide on How Much Vinyl You Need to Wrap a Vehicle .
Additional Manufacturer Resources
For official technical documentation, approved applications, adhesive performance, and installation recommendations, visit the Official 3M IJ180mC-10LSE Product Page .
IJ180mC-10LSE uses a permanent adhesive and is not designed for clean removability. Material durability, conformability, and warranty coverage depend on substrate compatibility, laminate selection, installation procedures, and manufacturer guidelines. Always test adhesion on the intended surface and review current technical specifications before installation.
Wholesale Pricing Available
Wholesale Pricing Available
For print shops and installers
Wholesale pricing for your next big project
Order custom prints and other Printara products at wholesale pricing. If you are not yet a wholesale customer, apply below to get started.
Apply for wholesaleCustom print discounts
Your discount is based on the total square footage of custom prints in your order. The highest tier reached applies.
| Custom print order size | Discount |
|---|---|
| 100–299 sq ft | 3% off |
| 300–499 sq ft | 5% off |
| 500–999 sq ft | 7% off |
| 1,000–1,499 sq ft | 9% off |
| 1,500 sq ft or more | 12% off |
10% off other products
Wholesale customers receive 10% off all other products. Services, including graphic design and installation, are excluded.
Ready to apply?
Submit the wholesale application to request access to wholesale pricing.
Start your wholesale application
California P65 Warning
California P65 Warning
Guides
How to set up your print file
How to set up your print file
File size and artwork dimensions
- Maximum file size: 1 GB.
- Artwork width: Make your artwork at least 0.5″ narrower than the media you select. For example, artwork printed on 60″ media should be no wider than 59.5″.
- Artwork size: Set up your file at the size you want it printed whenever possible. Smaller-scale files are accepted too. If you send a smaller file, tell us the final print size and scale in your order comments.
- Raster image resolution: Make sure your image has enough resolution for its final print size. Enlarging a low-resolution image can make it look blurry or pixelated.
Color
For standard artwork: We recommend sending RGB artwork with the sRGB IEC61966-2.1 color profile embedded. This gives our print software a consistent reference when converting colors for the selected printer and material.
For artwork using Printara Colors: Use the LAB values shown for the color. In Illustrator, create a LAB-defined spot-color swatch and keep it as a spot color in your vector file and production PDF. Preserving the spot-color definition is the preferred way to carry the Printara color target into production.
Prepare your artwork
- Images: Use an image resolution that suits the final print size. Low-resolution images may look blurry or pixelated.
- Fonts and placed images: In vector files, convert fonts to outlines, curves, or paths. Embed any images placed in your file.
- Artboard: Crop the artboard closely around your full design. Any blank space inside the artboard may be included in the printed output.
Accepted file types
We accept PDF, PSD/PSB, TIFF, JPEG, PNG, AI, EPS, and SVG files. To preserve Printara LAB spot colors, submit vector artwork or a PDF with spot colors retained. For raster artwork, submit a Lab-mode PSD, PSB, or TIFF.
Before you submit
Please send files that are ready to print. If your file is smaller than the intended print size, include the final size and scale in your order comments.
Printara may decline files that do not meet these guidelines. We do not review or correct every submitted file, so please check your artwork before sending it.
Need help with your artwork?
Our design team can help prepare or create your artwork. Submit a custom graphic design request.
How to set up contour cut lines
How to set up contour cut lines
- File should be supplied in AI, EPS, SVG, or PDF format with vector contour lines.
-
IMPORTANT: Contour lines must be assigned as a Spot Color named 'CutContour'.
To assign a spot color using Adobe Illustrator:
- Open the Swatches Palette. If the Swatches Palette is not readily visible, you may need to open it by selecting Swatches from the Windows menu.
- Click the 3 horizontal lines in the upper right corner of the Palette, and select New Swatch. This opens the New Swatch dialog.
- Enter CutContour as the name of the new swatch. This needs to be spelled exactly as shown here.
- Select Spot Color from the Color Type drop-down menu, and use the slider bars to create a color. The color is not important since it will not be printed.
- Click OK to close the dialogs.
- Select your cut paths and assign your new swatch color to those paths.
Note: You may use any vector-based drawing program you want. These instructions are specific to Adobe Illustrator. Most drawing programs will follow a similar process. If you have trouble, see the Help Files in your drawing program.
- Contour lines and print image must be supplied in the same file.
- Contour files must be at least 2" less than width of print media.
- Opacity of CutContour lines MUST be at 100%.
- DO NOT hide the CutContour layer or turn off the option to print.
Taking these steps allows us to seamlessly assign your CutContour lines. If followed correctly, the CutContour lines will NOT print. Failure to follow guidelines may result in delayed processing time.
PNG file types with transparent backgrounds are acceptable, but not recommended. Please be aware that PNG files work in a RGB colorspace, and WILL be converted to CMYK when sent to print. We are not responsible for any inaccuracy or color shift that occurs as a result of the conversion.
How square footage is calculated
How square footage is calculated
How Print Square Footage Is Calculated
Our products are priced by the amount of print media required to produce your project. Because your artwork is printed from a roll, the square footage used may be different from the finished square footage of your graphic.
Square Footage Is Based on the Media Used
Your print is produced from a fixed-width roll of media. This means your order is calculated using the amount of media required to produce the print — not just the finished area of the graphic itself.
36″ × 72″ Graphic Example
A 36″ wide graphic is produced on 48″ wide media. Even though the finished graphic is only 36″ wide, the full 48″ width of media is used for the 72″ print length.
Graphic
Projects That Require Panels
If your project is too wide to print in one piece, the calculator can divide it into overlapping panels.
Panels include a fixed 1″ overlap. The calculator determines the media width, orientation, number of panels, and total material required.
Already Know Your Square Footage?
Use the Square Footage tab instead of entering finished dimensions.
Enter the square footage you need and select the desired media width. The calculator will show the approximate length of material that square footage represents.
Frequently Asked Questions
Why is my calculated square footage larger than my graphic?
Do I need to select the correct media width myself?
Can my artwork be rotated to use less material?
How much smaller should my artwork be than the media?
What happens if my artwork cannot fit on one piece of media?
No Manual Math Required
Enter your finished dimensions on the product page and the calculator will determine the media required for your print.